DetailPage-MSS-KB

Microsoft small business knowledge base

Article ID: 951037 - Last Review: February 23, 2011 - Revision: 7.0

On This Page

INTRODUCTION

This article describes the TCP Chimney Offload, Receive Side Scaling (RSS), and Network Direct Memory Access (NetDMA) features that are available for the TCP/IP protocol in Windows Server 2008.

MORE INFORMATION

TCP Chimney Offload overview

TCP Chimney Offload is a networking technology that helps transfer the workload from the CPU to a network adapter during network data transfer. In Windows Server 2008, TCP Chimney Offload enables the Windows networking subsystem to offload the processing of a TCP/IP connection to a network adapter that includes special support for TCP/IP offload processing.

TCP Chimney Offload is available in all versions of Windows Server 2008 and Windows Vista. Both TCP/IPv4 connections and TCP/IPv6 connections can be offloaded if the network adapter supports this feature.

How to enable and disable TCP Chimney Offload in Windows Server 2008

TCP Chimney Offload can be enabled or disabled in the following two locations:
  • The operating system
  • The advanced properties page of the network adapter
TCP Chimney Offload will work only if it is enabled in both locations. By default, TCP Chimney Offload is disabled in both these locations. However, OEM installations may enable TCP Chimney Offload in the operating system, in the network adapter, or in both the operating system and the network adapter.

How to configure TCP Chimney Offload in the operating system

  • To enable TCP Chimney Offload, follow these steps:
    1. Use administrative credentials to open a command prompt.
    2. At the command prompt, type the following command, and then press ENTER:
      netsh int tcp set global chimney=enabled
  • To disable TCP Chimney Offload, follow these steps:
    1. Use administrative credentials to open a command prompt.
    2. At the command prompt, type the following command, and then press ENTER:
      netsh int tcp set global chimney=disabled
  • To determine the current status of TCP Chimney Offload, follow these steps:
    1. Use administrative credentials to open a command prompt.
    2. At the command prompt, type the following command, and then press ENTER:
      netsh int tcp show global

How to configure TCP Chimney Offload on the network adapter

  • To enable or disable TCP Chimney Offload, follow these steps:
    1. Open Device Manager.
    2. Under Network Adapters, double-click the network adapter that you want.
    3. On the Advanced tab, click Enabled or Disabled in the box next to the TCP offload entry.

      Note Different manufacturers may use different terms to describe TCP Chimney Offload on the Advanced properties page of the network adapter.

How TCP Chimney Offload coexists with other programs and services

When the TCP Chimney Offload technology offloads TCP/IP processing for a given TCP connection to a dedicated network adapter, it must coexist with other programs or services that rely on lower layer services in the networking subsystem. The following table shows how TCP Chimney Offload coexists with other programs and services.
Collapse this tableExpand this table
Program or serviceWorks together with TCP Chimney OffloadExpected behavior when both the service and TCP Chimney Offload are enabled
Windows FirewallYes If the firewall is configured to allow for a given TCP connection, the TCP/IP stack will offload that TCP connection to the network adapter.
Third-party firewallImplementation-specific Some firewall vendors have decided to implement their product in such a way that TCP Chimney Offload can be used while the firewall service is running. Refer to the firewall documentation to find out whether the product you are using supports TCP Chimney Offload.
Internet Protocol security (IPsec) policyNo If the system has an IPsec policy applied, the TCP/IP stack will not try to offload any TCP connections. This lets the IPsec layer inspect every packet to provide the desired security.
Network Adapter teaming service (This service is also known as the Load Balancing and Failover service. It is usually provided by an OEM.)Implementation-specificSome OEMs have decided to implement their network adapter teaming solutions so that they coexist with TCP Chimney Offload. See the network adapter teaming service documentation to determine whether you can use TCP Chimney offload together with this service.
Windows Virtualization (Hyper-V technology) No If you are using the Microsoft Hyper-V technology to run virtual machines, no operating system will take advantage of TCP Chimney offload.
Network monitoring tools, such as Network Monitor and Wireshark Implementation-specificSome network monitoring tools may coexist with TCP Chimney but may not monitor offloaded connections.
Network Load Balancing (NLB) service No If you configure the NLB service on a server, the TCP/IP stack does not offload TCP connections.
Cluster serviceYesHowever, note that TCP connections using the Network Fault Tolerant driver (NetFT.sys) will not be offloaded. NetFT is used for fault-tolerant inter-node cluster communication.
Network Address Translation (NAT) service (also known as the Internet Connection Sharing service) NoIf this service is installed and running, the TCP/IP stack does not offload connections.

How to determine whether TCP Chimney Offload is working

When TCP Chimney Offload is enabled in the operating system and in the network adapter, the TCP/IP stack tries to offload suitable TCP connections to the network adapter. To find out which of the currently established TCP connections on the system are offloaded, follow these steps:
  1. Use administrative credentials to open a command prompt.
  2. Type the following command, and then press ENTER:
    netstat –t
    You receive output that resembles the following:
    Active Connections
    
      Proto  Local Address          Foreign Address        State           Offload State
    
      TCP    127.0.0.1:52613        computer_name:52614       ESTABLISHED     InHost
      TCP    192.168.1.103:52614        computer_name:52613       ESTABLISHED     Offloaded
    
    In this output, the second connection is offloaded.
For more information about TCP Chimney offload in Windows Server 2003, click the following article number to view the article in the Microsoft Knowledge Base:
912222  (http://support.microsoft.com/kb/912222/ ) The Microsoft Windows Server 2003 Scalable Networking Pack release

How to enable and disable RSS in Windows Server 2008

To enable RSS, follow these steps:
  1. Use administrative credentials to open a command prompt.
  2. At the command prompt, type the following command, and then press ENTER:
    netsh int tcp set global rss=enabled
To disable RSS, follow these steps:
  1. Use administrative credentials to open a command prompt.
  2. At the command prompt, type the following command, and then press ENTER:
    netsh int tcp set global rss=disabled
To determine the current status of RSS, follow these steps:
  1. Use administrative credentials to open a command prompt.
  2. At the command prompt, type the following command, and then press ENTER:
    netsh int tcp show global
When you use a command to enable RSS, you receive the following message:
TCP Global Parameters
----------------------------------------------
Receive-Side Scaling State : enabled
Note By default, RSS is enabled.

How to enable and disable NetDMA in Windows Server 2008

To have us enable or disable NetDMA for you, go to the "Fix it for me" section. If you prefer to enable or disable NetDMA yourself, go to the "Let me fix it myself" section.

Fix it for me



To fix this problem automatically, click the Fix it button or link. In the File Download dialog box, click Run, and then follow the steps in the Fix it Wizard.


Enable NetDMA
Microsoft Fix it 50610
Disable NetDMA
Microsoft Fix it 50611


Notes
  • To make sure the Enable NetDMA package work, you must enable the NetDMA functionality. For more information about using NetDMA, click the following link:
    http://technet.microsoft.com/en-us/library/gg162716(WS.10).aspx (http://technet.microsoft.com/en-us/library/gg162716(WS.10).aspx)
  • This wizard may be in English only. However, the automatic fix also works for other language versions of Windows.
  • If you are not on the computer that has the problem, save the Fix it solution to a flash drive or a CD, and then run it on the computer that has the problem.

Then, go to the "Did this fix the problem?" section.



Let me fix it myself

To enable or disable NetDMA, follow these steps:
  1. Click Start, click Run, type regedit, and then click OK.
  2. Locate the following registry subkey, and then click it:
    HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters
  3. Double-click the EnableTCPA registry entry.
    Note If this registry entry does not exist, right-click Parameters, point to New, click DWORD Value, type EnableTCPA, and then press ENTER.
  4. To enable NetDMA, type 1 in the Value data box, and then click OK.
  5. To disable NetDMA, type 0 in the Value data box, and then click OK.
  6. If the EnableTCPA registry entry does not exist, enable the NetDMA functionality.

Did this fix the problem?

  • Check whether the problem is fixed. If the problem is fixed, you are finished with this section. If the problem is not fixed, you can contact support (http://support.microsoft.com/contactus) .
  • We would appreciate your feedback. To provide feedback or to report any issues with this solution, please leave a comment on the "Fix it for me (http://blogs.technet.com/fixit4me/) " blog or send us an email (mailto:fixit4me@microsoft.com?Subject=KB) message.
The third-party products that this article discusses are manufactured by companies that are independent of Microsoft. Microsoft makes no warranty, implied or otherwise, about the performance or reliability of these products.

APPLIES TO
  • Windows Web Server 2008
  • Windows Server 2008 Standard
  • Windows Server 2008 Enterprise
  • Windows Server 2008 Datacenter
  • Windows Server 2008 Standard without Hyper-V
  • Windows Server 2008 for Itanium-Based Systems
  • Windows Server 2008 Enterprise without Hyper-V
  • Windows Server 2008 Datacenter without Hyper-V
Keywords: 
kbenable kbnetworkmon kbnlb kbnetworkcard kbnetworkconnectivity kbexpertiseadvanced kbinfo kbhowto kbfixme kbmsifixme KB951037
Share
Additional support options
Ask The Microsoft Small Business Support Community
Contact Microsoft Small Business Support
Find Microsoft Small Business Support Certified Partner
Find a Microsoft Store For In-Person Small Business Support